TrenchcoatFullOfBats

In this, the worst timeline, I am glad that there is no need to add “allegedly”, as Zuck is clearly an alpha degen.

This is so Smorty

California already has a state fund for exactly this purpose, called the FAIR plan.

Institutional investors like pension funds selling a stock is kind of a big deal though, as a) there are a lot of them for a stock as “big” as Tesla, b) they are far less risk averse then individual investors, and c) the managers of these funds tend to pay attention to what other funds with similar holdings are doing. If one this big sells, others will wonder if they should get out now as well.

This could, in theory, be the start of a mass selloff of Tesla stock by institutional investors wanting to get out before the bubble bursts and they stop seeing gains from Tesla stock.

The 18% down figure is just over the last month. Scroll down to the short interest history to see how many months shorts have been up vs down.

I put on my robe and Linux hat

Some Romans getting relaxed

The Mupprix

This is a good point, the client is an important consideration. My setup is the similar, with Jellyfin running in docker in an Ubuntu Proxmox VM (host system CPU is an i7-6700t), but the client is an Nvidia Shield Pro, which so far has been able to handle everything Jellyfin throws at it, with the exception of AV1.

deleted by creator

Vikunja is great. Classic tasks, Gantt, tables and kanban - take your pick. Very stable as well, have been using it for years now.

How about a dreamatorium in a linen closet?

It is my time to shine! I’ve had 3 3D printers thus far: I started with an Ender 3 Pro that I modified extensively, converting it to direct drive, 3D printed belt tensioners, cable chains, fan ducts, upgraded board with quiet drivers, and a Raspberry Pi running Klipper. All of the modifications led to a decrease in quality over time.

I also had a Qidi for a while, and it was…fine. Not great, but serviceable. Not super repairable or upgradeable, and I had to use their version of the Cura slicer, which they did not do a good job of keeping up to date.

When the Ender 3 Pro started to become unreliable, I switched to the Elegoo Neptune 4 Pro, which is basically the final form of what I was trying to turn the Ender into, plus a bit extra. From the factory, it has direct drive, linear rails, runs klipper, has automatic bed leveling, filament runout detection, etc. It does NOT have wifi, but does have an ethernet port, which I prefer.

Using Fluidd is much better than Octoprint, and I’ve finally switched away from using Cura and am a convert to OrcaSlicer, which is EXCELLENT. It can send prints directly to the printer as well. It’s a great combination that I’m having a lot of fun with.

Full disclosure: I recently discovered that the version of Klipper this printer uses is out of date (2022) and does not fully comply with the klipper license, which I am NOT a fan of, but there is a very well documented way to “upgrade” to a “de-Elegood”, fully operational Klipper.

Preventing cam-out with a Phillips screw is like learning the ways of the Force. It takes patience and skill, something the Empire’s rigid Torx would never understand.

Denethor: Boromir would have used a claymore

Fantastic Fourplay

T-80: Lasted for 34 minutes before succumbing to crippling depression and taking itself permanently offline

Two things:

1. I was expecting a recipe at the end of that
2. CUT YOUR HAIR, JOSH

Disk space is definitely an issue, but I think I’ve got my single user instance dialed in on a 2 vcpu/4gb/30GB RAM Hetzner VPS; a cron job that runs at the first of every month deletes pictrs files over 30 days old. Currently at 74%.

A lot of bean memes died the day that job first ran.

Judging by the profile pic, probably factually incorrect animal documentaries